Ei Electronics Ei262 Spezifikationen Seite 1

Model Ei262Read and retain carefully for as long as the product is being used. Contains vital information on theoperation and installation. This leafl

- Next to a door, window, air vent or anywhere that it would be affected by draughts- Next to an extractor fan- Where it would be obstructed, e.g. by

11300mm150mm1 to 3 m1 to 3 mDEAD AIRDON'T LOCATEHERECO AlarmFigure 1. Location in room with a fuel burning appliance- 1 to 3m from appliance- Cei

12300mmCO AlarmCO Alarmabout1 to 2mFigure 3. Location in bedroom & roomsremote from the applianceFigure 2. Location in rooms withsloped ceilings-

134. INSTALLATION4.1 Mounting & Wiring your alarmThe Alarm is designed to be permanentlymounted, using its own built-in terminalblock to connect i

The Alarm must not be connected when the house wiring insulation is being checked with high Voltagesi.e. do not use an insulation tester on the alarm.

3. The house wiring must be connected to the terminal block on the mounting plate as follows:L: Live - connect to the house wires coloured brown or ma

7. Carefully align the mounting plate and screw into place. Connect the wires to the terminal block. Withrecessed wiring, ensure the rear gasket seals

(As a safety feature the units will all communicate with each other (provided they are within range) as installed i.e. without any HouseCoding. The re

If interconnected CO and Smoke/Heat Alarms are all sounding, theLOCATE switch on the Ei411H3 Remote Control should be pressed. Thiswill just leave the

4. Check that the RadioLINK Ei262 is house coded to all the other RadioLINK devices in the property bycounting the number of times the red light flash

1234567891011121314IMPORTANT INFORMATIONWhat to do when you alarm is activatedCARBON MONOXIDE - THE SILENT KILLERALARM POSITIONINGINSTALLATION4.1 Moun

When button testing units in sequence it is important to wait 15 seconds plus a further 6 seconds perrepeater between button tests (e.g. for a system

Do not connect these Alarms to any other model produced by another manufacturer, or to anyother model of Ei Alarm, apart from those listed above. Doin

4.4 Using RadioLINK interconnect and hard wired interconnect together.Hybrid systems can be used - for example to get the RadioLINK signal from an Ei2

(the horn will pause during the RF transmission). Any other installed interconnected devices should nowsound. Release the test button. The local alarm

5.2.8. TESTING WITH CARBON MONOXIDEThe unit can be tested with CO by using one of the kits that comes with CO either in a glass phial or aerosol can.

Do not paint the CO Alarm.Remove the CO Alarm when decorating. Do not allow water or dust to contaminate the alarm.Do not open or tamper with the CO A

(7) Reconnect the mains supply.(8) Wait 4 minutes for the new sensor to stabilise and then press the Test/Hush button - the horn shouldsound.Note: Whe

- CO Alarms don’t last indefinitely. CO Alarms are sophisticated electronic devices with many parts.Although the alarm and its component parts have un

The Ei262 CO Alarm has been tested to EN 300 220-1 V1.3.1 (2000-09) in accordance with therequirements of EN 300 220V1.1.1 (2000-09). These tests are

- Choose all appliances and vehicles which burn fossil fuels such as coal, oil, natural/bottled gas, paraffin,wood, petrol, diesel, charcoal etc. with

1. IMPORTANT INFORMATIONWARNING: The Alarm should be permanently wired to the mains by a qualified electrician inaccordance with IEE wiring regulation

10. GETTING YOUR CO ALARM SERVICEDIf your CO Alarm fails to work after you have carefully read all the instructions, checked the unit has beeninstalle

3112. TECHNICAL SPECIFICATIONSOperating Voltage : 230±10% VAC, 50HzPower : 1 Watt (90 mA)Power on Indicator : Green LightSensor : Electrochemical Sens

Initialisation Time : 70 seconds. On power up red and amber lights flash momentarily to show they are operational.Operating Temperature : -10°C to 40°

Audible Alarm : 85dB(A) minimum @ 3mSelf DiagnosticsSensor : Horn beep and amber fault light flashes every 40 seconds if a sensor fault is found.Recha

Repeater Function : To disable the Repeater function press and hold the test button until the alarm sounds and the RadioLINK red light turns on. Immed

Radiolink Base Ei168RCThe Ei262 CO Alarm can be interconnected to any of the RadioLINK Smoke/Heat/Fire Alarms such asthe Ei160 Series mounted on an Ei

14. TROUBLESHOOTINGTROUBLESHOOTING THE RF LINKIf when checking the RadioLINK interconnection some of the alarms do not respond to the button test,then

1. ALARM DOES NOT WORK WHEN THE TEST BUTTON IS PRESSED:- Check that the green mains power light is on. If it is off check the wiring, fuse, circuit b

If the unit continues to sound it is possibly defective and should be replaced. Follow the instructions inSection 10 “GETTING YOUR CO ALARM SERVICED”.

39B16587-R0-262-UC-ENG 15/4/09 3:38 PM Page 39

WHAT TO DO WHEN THE CARBON MONOXIDE ALARM IS ACTIVATED:(1) Open the doors and windows to ventilate the area.(2) Turn off all fuel appliances where pos

Aico LtdMile End Business Park, Maesbury Rd,Oswestry, Shropshire SY10 8NN, U.K.Tel: 0870 758 4000 www.aico.co.ukEi ElectronicsShannon, Co Clare, Irela

2. CARBON MONOXIDE - THE SILENT KILLER2.1 WHAT IS CARBON MONOXIDE ?Congratulations on becoming the owner of an Ei Carbon Monoxide Alarm. This will hel

Many cases of reported Carbon Monoxide poisoning indicate that while victims are aware they are notwell, they become so disorientated they are una

2.3 WHAT HAPPENS WHEN YOUR CO ALARM DETECTS CARBON MONOXIDE ?When the Ei262 CO Alarm detects potentally dangerous levels of CO, it flashes the red ala

Pre-Alarm: When the alarm detects over 50ppm CO the red light flashes every 2 seconds. This helpslocate CO leaks as the unit gives a visable indicatio

3. ALARM POSITIONING3.1 IDEALLY A CARBON MONOXIDE (CO) ALARM SHOULD BE INSTALLED IN:- Every room containing a fuel burning appliance- Remote rooms whe